|
Crop / object of treatment
|
Harmful plants
|
Preparation consumption rate, l/ha
|
Mix consumption rate, l/ha
|
Method, time and conditions of application. Application time for manual (machinery assisted) operations
|
Wait time (application frequency)
|
|
Spring wheat
|
Foxtail species
|
0.4 0.4 (А)
|
100-200 25-50
|
Planting spraying over vegetating weeds starting from 2 leaves stage to end of tillering (regardless of crop growth stage) -(3)
|
60(1)
|
|
Annual cereal weeds (foxtail species, barnyard grass, weed millet, oat grass, etc.)
|
0.4-0.6 0.4-0.6(А)
|
100-200 25-50
|
|
0,3
|
100-200
|
Planting spraying over vegetating weeds, at earliest ages of their growth – 2-3 leaves (regardless of crop growth stage) using mix with 200 l/ha of surfactant Satellite, L -(3)
|
|
Winter wheat
|
Annual cereal weeds (foxtail species, barnyard grass, weed millet, oat grass, corn grass, etc.)
|
0.4-0.6 0.4-0.6(А)
|
100-200 25-50
|
Planting spraying in spring starting from 2 leaves stage to end of tillering of annual cereal weeds (regardless of crop growth stage) -(3)
|
|
|
0,3
|
100-200
|
Planting spraying in sprig over vegetating weeds, at earliest ages of their growth – 2-3 leaves (regardless of crop growth stage) using mix with 200 l/ha of surfactant Satellite, L -(3)
|
|
(A) – aerial treatment
Application technique. Mix preparation method
Prepare the mix immediately before use.
For ground treatment:
Fill the sprayer tank with water to 3/4 of its volume, slowly add the entire preparation dose while stirring, and rinse the container with preparation remainders several times with water. Pour water after rinsing the preparation container to the sprayer tank and top up with remaining water until full while continuously stirring.
For aerial treatment:
Fill the refilling unit tank with water to 1/2, add the required preparation dose and top up the tank with water until full while continuously stirring it.
As the aircraft approaches the area of treatment, turn the hydraulic agitator on to additionally stir the mix (hydraulic agitator working time min. 2 minutes).
Mix preparation and filling into sprayers tanks of an An-2 plane shall be carried out with engine stalled and additional mix cleaning using ground-based filters.
Prepare the mix and fill the sprayer on dedicated sites, fill the refilling unit on fixed refilling stations (SEZ-10) that all are disinfected afterwards.
Recommended equipment:
For ground treatment – ground-based boom sprayers OPSh-15-01, OP-2000-2-01, Amazone 3000, or similar.
For aerial treatment – An-2 plane or Mi-2 helicopter.
Sprayers shall be setup, adjusted and spray nozzles installed in accordance with the Operation Manual for aircraft based spraying equipment.
The best result and quickest herbicide action of the preparation are achieved by:
- treatment at earlier stages of cereal weed growth (starting from 2 leaves);
- optimal selection of application periods (when the bulk of annual cereal weeds emerge);
- treatment under weather conditions favorable for plant growth and development.
Phytotoxicity
No cases of phytotoxicity to crops were recorded when recommendations on preparation application timing and rates were met. Do not apply on plantings weakened by frosts, heat, and pests.
Recommendations on protection of valuable flora and fauna objects
The preparation is of low hazard to bees and fish – Hazard Class 3.
Basic provisions of the ‘Guidelines for preventing bee poisoning with pesticides’ and following environmental regulations:
treat plants in morning and evening.
For ground application:
treat plants at wind speed up to 4 or 5 m/sec;
protection boundary zone for bees – min. 2-3 km;
bee’s flight time limitation – 3-4 hours.
For aerial application:
treat plants at wind speed of 0 m/sec;
protection boundary zone for bees – min. 5-6 km;
bee’s flight time limitation – 3-4 hours.
Warn apiary owners 4 or 5 days before treatment.
The preparation may be used within the sanitary zone of fishery water bodies.
